Fixes: - Support new model DES-3028G - 802.1D 2004 edition - Root Restriction (defined in 802.1Q-2005) - MLD Snooping v1 and v2 awareness - DoS attack Prevention - Asymmetric VLAN - IP-MAC-Port Binding v3.3 - IMPB auto recovery - ISM VLAN - IGMP authentication - VLAN trunking - Loopback detection v2.0 - Support Port-based QinQ (TPID of outer tag cannot be configured to 0x8100) - LLDP - Cable Diagnostics - Gratuitous ARP - Password encryption - Extend trusted host number to 10 entries and add mask function on trusted host - Support data driven multicast learned automatically - Support limited IP multicast address ranges - Product serial number can be displayed on GUI, CLI and be queried via SNMP. (From new shipment and burn-in serial number in H/W) - Password Recovery v1.1 - Support VLAN batch configuration - Be able to force the 802.1X client to go offline - Support 802.1X session timeout attribute - Can assign ingress/egress bandwidth control and 802.1p priority to the port according to the attributes dispatched from Radius Server - Support “show tech support” command for troubleshooting - Support configurable MDI/MDIX, it can be manual configure as Auto, Normal and Cross mode - Remark DSCP to 802.1p priority tag - Extend dynamic VLAN groups to 255 - Support three MAC address format: 11-22-33-44-55-66, 11:22:33:44:55:66 or 112233445566 - Add auto complete commands with extra parameter “force_agree”. Instead of popping up (Y/N) message while enter reset and reboot, it will be executed automatically - Remove all ACL entries by one command in CLI, Web and SNMP - Remove all trust host entries by one command in CLI, Web and SNMP - Display remaining ACL rules on Web/CLI - Add a SNMP MIB to support VLAN advertisement enable/disable function - Add show memory usage/percentage SNMP MIB - Add an OID to show port utilization - Add an OID to clear FDB and ARP table - Add ping command to user privilege - Stop contacting to TACAS+ server periodically before logging-in - Add “show VLAN” command by VLAN ID - Add "show FDB VLAN" command by VLAN ID - Support tagged ports column while show VLAN - Support forbidden router port - Add the ability to forward the unregistered multicast traffic to router port even when the ‘filter unregistered groups’ option is enabled - Add RFC2869 RADIUS extension standard to get 64 bits counters from two attribute "Acct-Input-Gigawords & Acct-Output-Gigawords" - Support to get NAS-ID from switch "system name" and can be configure NAS-ID - Support DHCP relay option 82 remote ID - Support DHCP local relay to insert option 82 information on DHCP broadcast packets in client’s VLAN - Block broadcast packet in DHCP relay - Ability to set the row number of terminal line - Add ARP-FDB table for easy set static entry to IP_MAC_Port binding tables - Extend ACL access id number from 256 to 65535 - Remove the display of MAC address from telnet log - Support broadcast storm control port shutdown log - Support port information on STP log event while STP topology changes - DLF rename to Unicast in storm control feature - Redirect embedded URL of D-Link logo to local OBU web site - Remove Web-UI welcome page - If SIM commander switch connects to member switch via tag ports, it is unable to upload/download member’s configuration - If STP is enabled on ports, ‘show ports’ command will cause screen to freeze - If STP is disabled, show ports and then reset, it will cause high CPU utilization - Show port list from left to right via SNMP - Config ports command lacks learning enable/disable parameter - While config multicast filter, unregistered groups on all ports cannot be learned as multicast router port - X authentication process with PEAP protocol takes a long time to complete - Incorrect display format while execute show current config - MAC address search issue on FDB monitor function - System interface cannot change to other VLAN while the switch is set as DHCP client - CPU high utilization while STP and LBD are enabled at the same time - Multicast client is unable to send leave packet if new VLAN is created on the switch - Filter unregistered groups on the port will block multicast control packets - IF customer uses SNMP module command and then powers off/on, switch will enter exception mode and reboot cyclically - SIM feature only works on default VLAN - While enable LACP connection, system interface cannot be accessed - Different ACL rules sequence will make ACL entries configure fail - SSH fatal error while running perl script from client - Dynamic VLAN assignment does not work if the RADIUS server is Juniper Funk Steel - While enable bandwidth control on port 25 and send packets over the rate limit from port 25 to 26, packet loss will occur from port 26 to 25
Скачать